Big Discount Desiccant Air Dryer System - 6.5 M3/Min Freeze Dryer Machine tr-06 for Air Compressor – Tianer

Product Paramters

TR Series Condition

TR Series Refrigerated Air Dryer

In the transmission process, as long as the ambient temperature is not lower than the air online pressure dew point，and the compressed air operating environment is not lower than the corresponding atmospheric pressure dew point ， no matter the transmission process or the operation process, there will be no condensate from the pipeline or pneumatic equipment again; Because the compressed air in the machine for secondary temperature return, so the practical temperature of compressed air in transmission is much higher than the dew point, the relatively moderate drop of air products in the tube (& LT; 40%).

The thick cloud in the compressed air of solid particles in the process of water vapor aggregation to serve as an aggregation of the nuclear effect will be along with condensate discharge closed, which means that freeze drying machine (person) “, the net effect of solid matter has “since it is not high to the requirement of inlet pretreatment, and occur on craft also does not have the possibility of secondary pollution, This is an advantage that some other boring methods (adsorption, absorption) do not have;

The flow resistance of the frozen dryer (cold drying machine) is smaller than that of the filter with the same flow rate, nor is it larger than that of the adsorption dryer (drying machine) and can adhere to the stability for a long time;

Refrigerated dryer (cold dryer) work energy consumption to adapt to its treatment of dew point, compared with the same standard adsorption boring method is lower;

Frozen dryer (cold dryer) basically no easy to wear parts, its primary life depends on the quality of the parts used;

Environmental protection
In response to the International Montreal Agreement, this series of models all use R134a and R410a environmentally friendly refrigerants, which will cause zero damage to the atmosphere and meet the needs of the international market.

The model is flexible and changeable
The plate heat exchanger can be assembled in a modular fashion, that is, it can be combined into the required processing capacity in a 1+1=2 manner, which makes the design of the whole machine flexible and changeable, and can more effectively control the raw material inventory.

High heat exchange efficiency
The flow channel of the plate heat exchanger is small, the plate fins are waveforms, and the cross-section changes are complicated. A small plate can obtain a larger heat exchange area, and the flow direction and flow rate of the fluid are constantly changed, which increases the flow rate of the fluid. Disturbance, so it can reach turbulent flow at a very small flow rate. In the shell-and-tube heat exchanger, the two fluids flow in the tube side and the shell side respectively. Generally, the flow is cross-flow, and the logarithmic average temperature difference correction coefficient is small.

There is no dead angle of heat exchange, basically achieving 100% heat exchange
Due to its unique mechanism, the plate heat exchanger makes the heat exchange medium fully contact the plate surface without heat exchange dead angles, no drain holes, and no air leakage. Therefore, compressed air can achieve 100% heat exchange. Ensure the stability of the dew point of the finished product.

Good corrosion resistance
The plate heat exchanger is made of aluminum alloy or stainless steel structure, which has good corrosion resistance and can also avoid secondary pollution of compressed air. Therefore, it can be adapted to various special occasions, including marine ships, with corrosive gases The chemical industry, as well as the more stringent food and pharmaceutical industries.

FAQ

1. Are you a factory or a trading company?
A: We are factory, and We have the right to export any country independently.

2. What is the specific address of your company?
A: No.23, Fukang Road, Dazhong Industrial Park, Yancheng, Jiangsu, China.

3. Do your company accept ODM & OEM?
A: Yes, of course. We accept full ODM & OEM.

4. What about the voltage of products? Can they be customized?
A: Yes, of course. The voltage can be customized according to your requirement.

5. Do your company offer spare parts of the machines?
A: Yes, of course, high quality spare parts are available in our factory.

6. What are your payment terms?
A: 30% T/T in advance, 70% T/T before delivery.

7. What payment ways do you accept?
A: T/T, Western Union.

8. How long will you take to arrange the goods?
A: For normal voltages,we can delivery the goods within 7-15 days. For other electricity or other customized machines, we will delivery within 25-30 days.

For more information or details, pls directly contact as.

Photos (Color can be customized)