Match up compressed refrigetated air dryer TR-10 for Compressor

Short Description:

The working principle of cooling and dew condensation is adopted, which is mainly composed of heat exchange system, refrigeration system and electrical control system. Compressed air first enters the pre-cooler for gas-gas or gas-water heat exchange, removing part of the heat energy, and then enters the cold and hot air exchanger, and has been cooled from the evaporator to the pressure dew point for heat exchange, so that the temperature of compressed air is further reduced. After that, the compressed air enters the evaporator and conducts heat exchange with the refrigerant. The temperature of the compressed air drops to 0-8℃. The moisture in the air is separated out at this temperature and discharged through the automatic drainer after being separated by the gas-water separator.

Send email to us

Product Detail

Product Tags

Product Paramters

TR series refrigerated air dryer	TR-10
Max air volume	400CFM
Power supply	220V / 50HZ (Other power can be customized)
Input power	3.30HP
Air pipe connection	RC2”
Evaporator type	Aluminum alloy plate
Refrigerant model	R410a
System max pressure drop	3.625 PSI
Display interface	LED dew point display, LED alarm code display,operation status indication
Intelligent anti-freezing protection	Constant pressure expansion valve and compressor automatic start/stop
Temperature control	Automatic control of condensing temperature/dew point temperature
High voltage protection	Temperature sensor
Low voltage protection	Temperature sensor and inductive intelligent protection
Weight(kg)	85
Dimensions L × W × H（mm)	770590990
Installation environment:	No sun, no rain, good ventilation, device level hard ground, no dust and fluff

TR Series Condition

1. Ambient temperature: 38℃, Max. 42℃
2. Inlet temperature: 38℃, Max. 65℃
3. Working pressure: 0.7MPa, Max.1.6Mpa
4. Pressure dew point: 2℃~10℃（Air dew point：-23℃~-17℃）
5. No sun, no rain, good ventilation, device level hard ground, no dust and fluff

TR Series Refrigerated Air Dryer

TR series refrigerated Air dryer	Model	TR-01	TR-02	TR-03	TR-06	TR-08	TR-10	TR-12
Max. air volume	m³/min	1.4	2.4	3.8	6.5	8.5	11	13.5
Power supply		220V/50Hz
Input power	KW	0.37	0.52	0.73	1.26	1.87	2.43	2.63
Air pipe connection		RC3/4"		RC1"	RC1-1/2"	RC2"
Evaporator type		Aluminum alloy plate
Refrigerant model		R134a		R410a
System Max. pressure drop	0.025
Intelligent control and protection
Display interface		LED dew point display, LED alarm code display,operation status indication
Intelligent anti-freezing protection		Constant pressure expansion valve and compressor automatic start/stop
Temperature control		Automatic control of condensing temperature/dew point temperature
High voltage protection		Temperature sensor
Low voltage protection		Temperature sensor and inductive intelligent protection
Energy saving	KG	34	42	50	63	73	85	94
Dimension	L	480	520	640	700	770	770	800
	W	380	410	520	540	590	590	610
	H	665	725	850	950	990	990	1030

Energy saving:
The aluminum alloy three-in-one heat exchanger design minimizes the process loss of the cooling capacity and improves the recycling of the cooling capacity. Under the same processing capacity, the total input power of this model is reduced by 15-50%

High Efficiency:
The integrated heat exchanger is equipped with guide fins to make the compressed air evenly exchange heat inside, and the built-in steam-water separation device is equipped with a stainless steel filter to make the water separation will be more thoroughly.

Intelligent：
Multi-channel temperature and pressure monitoring, real-time display of dew point temperature, automatic recording of accumulated running time, self-diagnosis function, display of corresponding alarm codes, and automatic protection of equipment

Environmental protection:
In response to the International Montreal Agreement, this series of models all use R134a and R410a environmentally friendly refrigerants, which will cause zero damage to the atmosphere and meet the needs of the international market.

Good corrosion resistance
The plate heat exchanger is made of aluminum alloy or stainless steel structure, which has good corrosion resistance and can also avoid secondary pollution of compressed air. Therefore, it can be adapted to various special occasions, including marine ships, with corrosive gases The chemical industry, as well as the more stringent food and pharmaceutical industries.

Attention

1. The flow pressure and temperature of compressed air should be within the allowable range of the nameplate;

2. The installation site should be ventilated, less dust, there is enough heat dissipation and maintenance space around the machine and can not be installed outdoors, to avoid rain and direct sunlight;

3. Cold drying machine is generally allowed without foundation installation, but the ground must be leveled;

4. Should be as close to the user point as possible to avoid too long pipeline;

5. There should be no detectable corrosive gas in the surrounding environment, especially pay attention to not coexist with ammonia refrigeration equipment in the same room;

6. The filter precision of the pre-filter of the cold drying machine should be appropriate, too high precision is not necessary for the cold drying machine;

7. The cooling water inlet and outlet pipe should be set independently, especially the outlet pipe can not be shared with other water cooling equipment, to avoid pressure difference caused by blocked drainage;

8. At any time to keep the automatic drainer drainage smooth;

9. Do not start the cold drying machine continuously;

10. Cold drying machine actual processing of compressed air parameters, especially the inlet temperature, working pressure and rating does not conform, according to the sample provided by the "correction coefficient" for correction, in order to avoid overload operation.